+
−# This is the opamp library for LISO  ghh mpq 4/98 version 1.3
+
−# expanded for version 1.8 gerhard.heinzel@nao.ac.jp 12/2000
+
−#
+
−# Everything is in SI units;
+
−# 'a0' is the DC open loop gain;
+
−# 'gbw' the Gain-Bandwidth product for typical operating frequencies,
+
−# 'un' and 'in' the voltage and current noise spectral densities
+
−# in V/sqrt(Hz) and A/sqrt(Hz), respectively.
+
−# 'uc' and 'ic' are their respective 1/f corner frequencies
+
−#
+
−# Unless mentioned explicitely, I entered the "typical" values for the
+
−# cheapest grade at 25 degrees. a0 should usually
+
−# be uncritical; I entered the "typical" values for the cheapest grade for
+
−# large loads. The 1/f corner frequencies 'uc' and 'ic' (in Hz) are often
+
−# not well defined. poles and zeroes of the open-loop transfer function 
+
−# are interpreted as additional feratures to the 1/f frequency response
+
−# given by a0 and gbw.
+
−# 
+
−# 'umax' (in Volt), 'imax' (in Ampere) and 'sr' (in V/s)
+
−# describe the output capabilities (used by the 'maxinput' instruction).
+
−# I usually entered the values for +-15V supplies.
+
−#
+
−# Please note: This library is experimental, incomplete and may be wrong.
+
−# Whenever the individual op-amp properties become important, you must
+
−# check yourself that the correct values are entered below.
+
−#
+
−
+
−name=op00 # (almost) ideal OpAmp
+
−a0=1e12
+
−gbw=1e15
+
−un=0
+
−uc=1
+
−in=0
+
−ic=1
+
−umax=12
+
−imax=.02
+
−sr=1e12
+
−
+
−name = op07
+
−a0 = 4e5
+
−gbw = 561k # fitted from measurement
+
−un = 10e-9
+
−uc = 1
+
−in = 0.13e-12
+
−ic = 100
+
−umax=12
+
−imax=0.02
+
−sr=0.3e6
+
−pole=2M # fitted from measurement
+
−delay=74n # fitted from measurement
+
−# Rout=90 Ohm, Cin=23 pF (measured)
+
−
+
−name = op177
+
−a0 = 6e6
+
−gbw = 721k # fitted from measurement
+
−un = 9.4e-9 # from measurement
+
−uc = 1.2 # from measurement
+
−in = 0.2e-12 # from measurement
+
−ic = 2.5 # from measurement
+
−pole=7.53M 1.78 # fitted from measurement
+
−pole=1.66M # fitted from measurement
+
−delay=30n # fitted from measurement
+
−umax=12
+
−imax=0.02
+
−sr=0.3e6
+
−
+
−
+
−name = tle2037
+
−a0 = 5e6
+
−gbw = 76e6
+
−un = 2.5e-9
+
−uc = 10
+
−in = 1.5e-12
+
−ic = 100
+
−umax=12
+
−imax=0.02
+
−sr=7.5e6 # ???
+
−
+
−name = lt1037  
+
−a0 = 5e6
+
−gbw = 53M
+
−un = 2.5n
+
−uc = 2
+
−in = 0.4p
+
−ic = 120
+
−pole = 870k # fitted from PMI OP37 data sheet
+
−zero = 1.67M
+
−pole = 17.1M
+
−umax=12
+
−imax=0.02
+
−sr=15e6
+
−
+
−
+
−name = lt1037nopole
+
−a0 = 5e6
+
−gbw = 53M
+
−un = 2.5n
+
−uc = 2
+
−in = 0.4p
+
−ic = 120
+
−umax=12
+
−imax=0.02
+
−sr=15e6
+
−
+
−
+
−name = lt1007
+
−a0 = 20e6
+
−gbw = 8e6
+
−un = 2.5e-9
+
−uc = 10
+
−in = 0.4e-12
+
−ic = 100
+
−umax=12
+
−imax=0.02
+
−sr=2.5e6
+
−
+
−
+
−name = opa671 # fast FET, for photodiode transimpedance
+
−a0 = 1e4
+
−gbw = 35e6
+
−un = 10e-9
+
−uc = 1e3
+
−in = 2e-15
+
−ic = 2
+
−umax=12
+
−imax=50m
+
−sr=100e6
+
−
+
−name = ad712 # also ad711, ad713
+
−a0=400e3
+
−gbw=4e6
+
−pole=7e6 1
+
−zero=10e6 1
+
−un=16e-9
+
−uc=100
+
−in=0.01e-12
+
−ic=1000 # guessed
+
−umax=12
+
−imax=0.02
+
−sr=20e6
+
−
+
−
+
−name = op27
+
−a0 = 1.5e6
+
−gbw = 8e6
+
−un = 3.2e-9 
+
−uc = 2.7 # from PMI data sheet
+
−in = 0.4e-12
+
−ic = 140 # from PMI data sheet
+
−pole = 6e6
+
−umax=12
+
−imax=0.02
+
−sr=2.8e6
+
−
+
−
+
−name = lt1028 # low noise, beware of 400 kHz noise peak
+
−a0 = 30e6
+
−gbw = 72e6
+
−pole = 780k
+
−zero = 3.14M
+
−delay = 7.5n
+
−un = 0.85e-9
+
−uc = 3.5 
+
−in = 1e-12
+
−ic = 250
+
−umax=12
+
−imax=0.02
+
−sr=15e6
+
−
+
−
+
−name = ad829 # fast lownoise voltage-feedback, No ext. comp., measured at gain 1
+
−a0 = 1e5 # 100V/mV
+
−gbw = 85M
+
−un = 1.7e-9
+
−uc = 30 
+
−in = 1.5e-12
+
−ic = 100 # not given in datasheet
+
−umax=12
+
−imax=0.05
+
−sr=260e6
+
−zero = 19.3M # fitted from measurement
+
−pole = 53.4M 5.1 # fitted from measurement
+
−zero = 76.5M 4.7 # fitted from measurement
+
−pole = 13M # fitted from measurement
+
−delay = 1.9n # fitted from measurement
+
−
+
−name=opa655 # fast 5V FET
+
−a0 = 834.265 #from fitting OPA655.dat 
+
−gbw = 214597e3
+
−pole  = 169968e3
+
−un=6e-6
+
−uc=5000
+
−in=1.3e-15
+
−ic=1 # not given
+
−
+
−name = ad797 # very low noise
+
−a0=20M    # data sheet
+
−gbw=120M   # fitted from measured data (3 pcs AD797AN 15V DIP)
+
−un=0.9n # data sheet
+
−uc=100 # data sheet
+
−in=2p # data sheet
+
−ic=100 # not given
+
−pole=3.6M # pole0  # fitted from measured data (3 pcs AD797AN 15V DIP)
+
−zero=12.7M  # zero0  # fitted from measured data (3 pcs AD797AN 15V DIP)
+
−zero=23M  # zero1  # fitted from measured data (3 pcs AD797AN 15V DIP)
+
−pole=85M # pole1  # fitted from measured data (3 pcs AD797AN 15V DIP)
+
−pole=129M 3 # pole2  # fitted from measured data (3 pcs AD797AN 15V DIP)
+
−pole=207M 1.6 # pole3  # fitted from measured data (3 pcs AD797AN 15V DIP)
+
−delay=2.5n  # fitted from measured data (3 pcs AD797AN 15V DIP)
+
−umax=12 # data sheet
+
−imax=30e-3 # data sheet
+
−sr=20e6 # data sheet
+
−
+
−name=opa2604 # also opa604 single
+
−a0=1e5
+
−gbw=17.7e6
+
−un=10e-9
+
−uc=200
+
−in=6e-15
+
−ic=1
+
−pole=1.17e6 # fitted from data sheet
+
−zero=3.3e6
+
−pole=12.5e6
+
−umax=12
+
−imax=35e-3
+
−sr=25e6
+
−
+
−name=lt1001
+
−a0=8e5
+
−gbw=8e5
+
−un=10e-9
+
−uc=4
+
−in=.12e-12
+
−ic=70
+
−
+
−name=op275 # slow rail-to-rail
+
−a0=250e3
+
−gbw=9e6
+
−un=6e-9
+
−uc=6
+
−in=1.5e-12
+
−ic=120
+
−
+
−name=tle2227 # standard dual low noise opamp
+
−a0=44668359 #153 dB
+
−gbw=15e6 
+
−un=2.5e-9
+
−uc=10 # guessed
+
−in=0.4e-12
+
−ic=100 # guessed
+
−pole=20e6 # guessed
+
−zero=30e6
+
−pole=40e6
+
−delay=1n
+
−umax=12
+
−imax=0.02
+
−sr=2.8e6
+
−
+
−name=pa85 # apex high voltage high current high speed opamp
+
−a0=3e5 #110dB
+
−gbw=7e6 #cc=68pF
+
−pole=7e6 #cc=68pF
+
−un=4e-9
+
−uc=2e3
+
−in=1e-15 # not given
+
−ic=1000 # not given
+
−umax=120 # in our circuits
+
−imax=0.2
+
−sr=1000e6
+
−
+
−name=l2724
+
−a0=1e4
+
−gbw=1.2e6
+
−pole=1.2e6 # assumed
+
−un=67e-9 # guessed from rms
+
−uc=100 # free guess
+
−in=1.35e-9 # guessed from rms
+
−ic=50 # free guess
+
−umax=12 # with 14 V supply
+
−imax=1 # 1 Ampere!!
+
−sr=1e6
+
−
+
−name=L165 # sgs-thompson high current op amp
+
−a0=3e4 # 90 dB from data sheet fig. 3
+
−gbw=8.3M # fitted from measurement
+
−pole=3.17M # fitted from measurement
+
−delay=20n # fitted from measurement
+
−un=20e-9 # guessed from rms
+
−uc=100 # free guess
+
−in=1.e-9 # guessed from rms
+
−ic=50 # free guess
+
−umax=13 # with 15 V supply
+
−imax=3 # 3 Ampere!!
+
−sr=6e6
+
−
+
−name=tle2084 # also tle2081, tle2082
+
−a0=3e5 # 110dB
+
−gbw=10e6
+
−pole=10e6
+
−un=11.6e-9
+
−uc=500 # guess
+
−in=2.8e-15
+
−ic=100 # guess
+
−umax=13
+
−imax=25e-3
+
−sr=40e6
+
−
+
−name=tle2071 # also tle2072, tle2074?
+
−a0=3e5 # 100dB
+
−gbw=10e6
+
−pole=10e6
+
−un=11.6e-9
+
−uc=500 # guess
+
−in=2.8e-15
+
−ic=100 # guess
+
−umax=13
+
−imax=25e-3
+
−sr=40e6
+
−
+
−name=ina103_1000
+
−a0=1000
+
−gbw=100M
+
−un=1e-9
+
−uc=100
+
−in=2e-12
+
−ic=200
+
−umax=12
+
−imax=40m
+
−sr=15e6
+
−
+
−name=buf634
+
−a0=0.9  # 100 Ohm load
+
−gbw=160M # Wide Bandwidth Mode, otherwise 20 MHz
+
−un=4e-9 # at 10 kHz
+
−uc=100 # unknown !
+
−in=1e-9 # unknown !
+
−ic=50 # unknown !
+
−umax=12
+
−imax=0.25
+
−sr=2000e6
+
−
+
−name=opa620
+
−a0=1000 # 60 dB only
+
−gbw=200M
+
−un=2.5e-9
+
−uc=5k # guess
+
−in=2.3e-12
+
−ic=1k # guess
+
−umax=3
+
−imax=100e-3
+
−sr=250e6
+
−pole=250M
+
−
+
−name=ne5532
+
−a0=50e3
+
−gbw=10e6
+
−pole=5M
+
−un=5e-9
+
−uc=100 # guess
+
−in=0.7e-12
+
−ic=300 # guess
+
−umax=13
+
−imax=20e-3
+
−sr=9e6
+
−
+
−name=ha5002
+
−a0=0.995
+
−gbw=110e6
+
−un=5e9 # guess from 18e-6 Vpp in 1 MHz
+
−uc=100 # guess
+
−in=1e-12 # free guess
+
−ic=100 # free guess
+
−umax=12
+
−imax=.22
+
−sr=1.3e9
+
−
+
−name=el2099_2 # with 2*510 Ohm resistors for gain=2
+
−a0=2
+
−gbw=178M
+
−pole=45M 0.835
+
−delay=930p
+
−umax=12
+
−imax=0.8
+
−sr=1e9
+
−un=7e-9 # inver. current noise * 250 Ohm
+
−uc=2k
+
−in=3.5e-12 # noniv. current noise
+
−ic=10k
+
−
+
−name=el2099_1
+
−a0=1
+
−gbw=178M
+
−pole=45M 835m
+
−delay=930p
+
−umax=12
+
−imax=0.8
+
−sr=1e9
+
−un=14e-9 # current noise * 500 Ohm
+
−uc=10k
+
−in=25e-12 
+
−ic=10k
+
−
+
−name=max4106
+
−a0=1e5
+
−gbw=908M # from closed-loop gain fit & stability considerations
+
−pole=653M
+
−delay=300p
+
−umax=3.5
+
−imax=80m
+
−sr=275e6
+
−un=.75e-9 # !!! best ever
+
−uc=1k
+
−in=2.5e-12
+
−ic=10k
+
−
+
−name=ad8057 # parameters fitted from data sheet
+
−a0=367 # 55db
+
−gbw=112M
+
−delay=485p
+
−umax=3.9
+
−imax=30m
+
−sr=850M
+
−un=7n # fit = 6.5
+
−uc=332
+
−in=0.7p # fit = 0.85
+
−ic=2.4k
+
−
+
−name=max4100 # parameters fitted from data sheet
+
−a0=367 # 55db
+
−gbw=112M
+
−pole=200M
+
−delay=485p
+
−umax=3.9
+
−imax=30m
+
−sr=850M
+
−un=7n # fit = 6.5
+
−uc=332
+
−in=0.7p # fit = 0.85
+
−ic=2.4k
+
−
+
−name=max4101 # parameters fitted from data sheet
+
−a0=367 # 55db
+
−gbw=112M
+
−pole=200M
+
−delay=485p
+
−umax=3.9
+
−imax=30m
+
−sr=850M
+
−un=7n # fit = 6.5
+
−uc=332
+
−in=0.7p # fit = 0.85
+
−ic=2.4k
+
−
+
−name=op284
+
−a0=1e6
+
−gbw=16M # fitted from measurement
+
−pole=800k # fitted from measurement
+
−zero=2.7M # fitted from measurement
+
−delay=9n # fitted from measurement
+
−un=3.9e-9
+
−uc=20
+
−in=0.4e-12
+
−ic=100
+
−umax=15
+
−imax=10e-3
+
−sr=4e6
+
−
+
−name=opa627
+
−a0=630957 # 116 dB
+
−gbw=16M
+
−un=4.8e-9
+
−uc=100
+
−in=2.5e-15
+
−ic=100 # not given
+
−umax=12
+
−imax=.045
+
−sr=55e6
+
−
+
−name=tl084
+
−a0=200e3
+
−gbw=3M
+
−un=18n
+
−uc=300
+
−in=0.01p
+
−ic=300 # guess
+
−umax=12
+
−imax=0.0166666666666667
+
−sr=13e6
+
−delay=25n # from (hand-drawn) curve in data sheet
+
−
+
−name=tl074 # same as tl084
+
−a0=200e3
+
−gbw=3M
+
−un=18n
+
−uc=300
+
−in=0.01p
+
−ic=300 # guess
+
−umax=12
+
−imax=0.0166666666666667
+
−sr=13e6
+
−delay=25n # from (hand-drawn) curve in data sheet
+
−
+
−name=lt1124  # same as lt1125, improved dual/quad OP27
+
−a0=15e6      # from data sheet
+
−gbw=14.6M    # fitted from measured data ghh 4/2002
+
−pole=200k    # fitted from measured data ghh 4/2002
+
−zero=800k    # fitted from measured data ghh 4/2002
+
−pole=200k    # fitted from measured data ghh 4/2002
+
−zero=800k    # fitted from measured data ghh 4/2002
+
−zero=9.4M    # fitted from measured data ghh 4/2002
+
−delay=18.9n  # fitted from measured data ghh 4/2002
+
−un=2.7n      # from data sheet
+
−uc=2.3       # from data sheet
+
−in=0.3p      # from data sheet
+
−ic=100       # from data sheet
+
−sr=4.5e6     # from data sheet
+
−umax=12      # from data sheet
+
−imax=0.02    # from data sheet
+
−
+
−
+
−
+
−name=ad8628 # single-supply chopper at 5V
+
−a0=1e7 # 140dB
+
−gbw=2.5e6
+
−sr=1e6
+
−umax=5
+
−imax=0.03
+
−un=22e-9
+
−uc=1e-6 # no 1/f noise!
+
−in=5e-15
+
−ic=1e-6 # no 1/f noise!
+
−
+
−
+
−name=ad8048
+
−a0=2500 # 68dB
+
−gbw=260M # stability only for G>2 not entered
+
−un=3.8e-9
+
−in=1e-12
+
−uc=100
+
−ic=100 #guess
+
−sr=1e9 
+
−
+
−name=ad8065
+
−a0=500000 # 113dB from data sheet
+
−gbw=65M # from data sheet
+
−delay=1.7n# guessed from data sheet
+
−un=7n #  from data sheet
+
−uc=3k # from data sheet
+
−in=0.6f # from data sheet
+
−ic=3k # guessed
+
−umax=5 # supply dependent
+
−imax=0.03
+
−sr=160e6 # from data sheet
+
−
+
−name=ad811_g10 # +-5V, Gain +10
+
−a0=10
+
−gbw=1000M
+
−pole=70M .7
+
−umax=3
+
−imax=0.1
+
−sr=400e6
+
−
+
−name=opa690
+
−a0=1400 # 63dB from data sheet
+
−gbw=250M # from data sheet
+
−pole=250M# guessed from data sheet
+
−un=5.5n #  from data sheet
+
−uc=3k # from data sheet
+
−in=3.1p # from data sheet
+
−ic=3k # guessed
+
−umax=3.9 # supply dependent
+
−imax=0.19
+
−sr=1000e6 # from data sheet
+
−
+
−name=ad8608
+
−a0=1e6
+
−gbw=10e6
+
−pole=15e6
+
−sr=5e6
+
−umax=2
+
−imax=.08
+
−un=6.5e-9
+
−uc=1k
+
−in=0.01e-12
+
−ic=1k
+
−
+
−name=lf353
+
−a0=100e3
+
−gbw=4e6
+
−pole=10e6
+
−delay=1e-8
+
−sr=13e6
+
−un=16e-9
+
−uc=200
+
−in=0.01e-12
+
−ic=200
+
−umax=12
+
−imax=10e-3
+
−
+
−name=pztfet1 # MOSFET with open load (nopen50.dat)
+
−a0=21
+
−gbw=421k
+
−pole=12.4k 0.585
+
−zero=11.77k
+
−delay=261n
+
−sr=10e6
+
−un=1e-9
+
−uc=1
+
−in=1e-12
+
−ic=1
+
−umax=12
+
−imax=10e-3
+
−
+
−name=pztfet2 # MOSFET with Jena PZT njena50.dat
+
−a0=21.3
+
−gbw=322.8k
+
−pole=9.6k 0.257
+
−zero=18.6k
+
−delay=1n
+
−sr=10e6
+
−un=1e-9
+
−uc=1
+
−in=1e-12
+
−ic=1
+
−umax=12
+
−imax=10e-3
+
−
+
−name=pztfet3 # MOSFET with PI PZT npi30.dat
+
−a0=22.2
+
−gbw=18.4k
+
−pole=12.82k .052
+
−zero=1.09
+
−delay=1n
+
−sr=10e6
+
−un=1e-9
+
−uc=1
+
−in=1e-12
+
−ic=1
+
−umax=12
+
−imax=10e-3
+
−
+
−name=op200 # worst case
+
−a0=1e6
+
−gbw=500e3
+
−pole=2M
+
−sr=0.1e6
+
−un=18e-9
+
−uc=100
+
−in=0.4e-12
+
−ic=10
+
−umax=11
+
−imax=20e-3
+
−
+
−name=opa657
+
−a0=3000 # 70dB
+
−gbw=1600e6
+
−pole=200M
+
−un=4.8e-9
+
−uc=2k
+
−in=1.3e-15
+
−ic=1
+
−sr=700e6
+
−umax=3.9
+
−imax=50e-3
+
−
+
−name=ad8674
+
−a0=6e6
+
−gbw=14.7M
+
−pole=1.75M
+
−zero=2.83M
+
−zero=23.5M
+
−delay=12.3n
+
−un=2.8e-9
+
−uc=5 # guess
+
−in=0.3e-12
+
−ic=100 # wild guess
+
−sr=4e6
+
−umax=12
+
−imax=0.02
+
−
+
−name=ad745
+
−a0=4e6
+
−gbw=20M
+
−pole=70M
+
−delay=12.3n
+
−un=2.9e-9
+
−uc=70 # guess
+
−in=7e-15
+
−ic=100 # wild guess
+
−sr=12.5e6
+
−umax=12
+
−imax=0.02
+
−
+
−name=ad706
+
−a0=2e6
+
−gbw=800k
+
−un=17e-9
+
−uc=3
+
−in=50e-15
+
−ic=10
+
−sr=0.15e6
+
−delay=50n
+
−umax=14
+
−imax=0.01
+
−
+
−name = op270 # data from data sheet, fit in c/filter/op/op270
+
−a0 = 700e3
+
−gbw = 6e6
+
−pole=1.32M
+
−zero=1.73M
+
−zero=20M
+
−delay=21n
+
−un = 3.2e-9 
+
−uc = 2.7 # from PMI data sheet
+
−in = 0.6e-12
+
−ic = 140 # from PMI data sheet
+
−umax=13.5
+
−imax=0.002 # 10V in 5 k
+
−sr=2.4e6
+
−
+
−name = ad8005
+
−a0 = 1000
+
−gbw = 200M
+
−un = 4n
+
−uc = 300
+
−in = 1.1p # noninverting, inverting = 9.1
+
−ic = 3k
+
−umax = 3
+
−imax = 0.01
+
−sr = 280e6